Red RTV Silicone Gasket Maker

Gasket Maker Manufacturer High Temperatrue to 650 F (343 C) Low Volatile Perfect Oil Resistance OEM Specification Quality

PRODUCT DESCRIPTION        SBONDHigh Temperature RTV Gasket Maker is a single component,room temperature, vulcanizing (RTV),  gasketing compound designed to provide reliable formed-in-place gaskets for mechanical assemblies. 

       This material cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket.  The product resists aging, weathering and thermal cycling without hardening,shrinking or cracking.  Designed to provide increased oil resistance and complies to extended warranty requirements.

PRODUCT BENEFITS·  Improved oil resistance·  Sensor safe, non-corrosive·  Good adhesion and flexibility·  Replaces most cut gaskets·  Can be used as a gasket maker or dressing·  Non-flammable, Non-toxic·  Low odor   TYPICAL APPLICATIONS·  Oil pans·  Transmission pans·  Valve covers·  Valves and guides·  Timing gear covers·  Differential covers

DIRECTIONS FOR USEFor assembly as a form-in-place gasket1. Remove all previous material from mating surfaces..2. For best results, clean and dry all surfaces with a residue-free solvent..3. Cut nozzle to desired bead size, 1/16 to 1/4 in diameter. An 1/8 bead is usually sufficient for most applications.4. Remove cap, puncture tube or cartridge seal and attach extension nozzle.5. Apply a continuous and even bead of silicone to onesurface, first tracing the internal areas of the gasket configuration, then all surrounding bolt holes.6. Assemble parts immediately while silicone is still wet.Secure or tighten to recommended torque specs.7. Re-torque will not be necessary after the product has cured.

For assembly as a gasket dressing1. Repeat steps 1 through 4 as in previous section.2. Apply a thin film of silicone to one surface to be sealed.3. Place the pre-cut gasket onto silicone film.4. Apply a second thin film to pre-cut gasket surface.5. Remove any excess and assemble parts immediately.Note: Product is not recommended for use as a cylinder head gasket or head gasket sealant.

For Cleanup1. Allow excess material to extend beyond the extension nozzle or aerosol tip to cure, sealing and protecting the remaining product from moisture.  For reuse, simply remove the cured product from the tip.2. Remove uncured product from parts and hand-tools with a dry cloth.  If skinned over, break film with a dry cloth to remove as much as possible. 3. Clean hands with a dry cloth or hand cleaner.

GENERAL INFORMATIONThis product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials.

( function(){ var aBigImageSrc = [ 'http://i00.i.aliimg.com/photo/v5/255931246_1/Red_RTV_Silicone_Gasket_Maker.jpg' , 'http://i00.i.aliimg.com/photo/v5/255931246_2/Red_RTV_Silicone_Gasket_Maker.jpg' , 'http://i00.i.aliimg.com/photo/v5/255931246_3/Red_RTV_Silicone_Gasket_Maker.jpg' , 'http://i00.i.aliimg.com/photo/v5/255931246_4/Red_RTV_Silicone_Gasket_Maker.jpg' , 'http://i00.i.aliimg.com/photo/v5/255931246_5/Red_RTV_Silicone_Gasket_Maker.jpg' , 'http://i00.i.aliimg.com/photo/v5/255931246_6/Red_RTV_Silicone_Gasket_Maker.jpg' ]; var oProductShow = new AE.run.minisite.productShow(); oProductShow.init( { 'aImgSrc': aBigImageSrc } ); } )(); Red RTV Silicone Gasket Maker